Planning a Business Aviation Stand for Hall A1 at AERO 2027
How to plan an exhibition stand for Hall A1 at AERO 2027 in Friedrichshafen: schedule, stand brief, layout, meeting capacity and the dates to confirm with the organizer.

Table of Contents
Introduction
The business aviation side of AERO 2027 is short. The organizer runs the hub for two and a half days, so a stand that needs a full day to warm up will miss most of its show. Planning for Hall A1 starts with that constraint.
This guide covers what we know about the hall, how to write a stand brief that fits a B2B-heavy audience, and which details are still unconfirmed and need a direct answer from the organizer.
Key Takeaways
- The Business Aviation Show Hub (Hall A1 and the Business Aviation Dome) runs April 14–16, 2027, and the organizer describes it as two and a half days. The show as a whole continues through April 17.
- Hall A1 gets its own entrance, the Business Aviation Stage and the first Air Charter Expo Regional – Europe, so visitor flow will differ from past years.
- Decide the stand's job before the finishes. Charter operators, OEMs and avionics suppliers need different floor plans.
- The organizer has published 2027 setup and dismantling times. Setup runs April 7 to 13, and dismantling runs from Saturday, April 17 to Tuesday, April 20.
What will Hall A1 look like in April 2027
According to the organizer’s announcement, the business aviation segment concentrates in Hall A1 and the Business Aviation Dome from April 14 to 16, with the Friday closing earlier than the rest of the show.
Several things change in the hall itself:
- Hall A1 is set to be fully occupied.
- It has its own visitor entrance.
- The conference stage moves into the hall as the Business Aviation Stage.
- The inaugural Air Charter Expo Regional – Europe, organized with The Air Charter Association and Business Air News, is hosted inside it (AFM).
- Helicopters move to Hall A2, nearer to business aviation and flight schools.
The organizer says the business aviation hub brings together more than 400 international exhibitors. That is the organizer's own figure, and it covers the hub as a whole, not Hall A1 alone. For the 2026 show as a whole, the organizer reported 860 exhibitors from 50 countries.
I did not find a published exhibitor list or floor plan for Hall A1 in 2027. Before you commit to a position, ask the organizer where the entrance, the stage and the Air Charter Expo area sit in the hall. Those three decide where visitors walk.
Also Read: How 10x10 Booths Helps Exhibitors Prepare for Hannover Messe 2027
Start with the brief, not the finishes
Most teams spend too much time choosing finishes before deciding what the stand needs to achieve. In business aviation that mistake is expensive, because the audiences behave differently.
A charter operator selling to brokers needs closed meeting space and somewhere to host. An OEM or completion center needs room for cabin samples, materials and a display that explains the work. An avionics supplier needs a demo station where a visitor can touch the product. Most exhibitors need two of these, and the floor plan has to choose which one gets the front of the stand.
Write the brief in four lines before talking to any designer:
- Who must walk onto the stand (names of roles or companies, not "decision makers").
- What they should see in the first ten seconds.
- What happens in the first conversation, and where.
- What the team follows up on after the show.
If you can't fill in line three, the stand isn't ready to be designed.
Choose the stand size by how many conversations run at once
Count the people on your team and the meetings you expect to run in parallel, then size the stand to that number. Square meters follow from it.
Open sides matter more than total area in a hall like A1. A corner or peninsula stand with two or three open sides catches walking traffic from more directions than an inline stand twice its depth. An island gives the most freedom and the highest cost. Whichever you book, check where the hall's entrance and stage will send people before you pick the side that faces the aisle.
Height and structure limits are set by the venue’s technical guidelines. Get the 2027 guidelines from the organizer before you fix any height, rigging or electrical detail, and treat figures quoted for earlier AERO shows as unconfirmed.
Also Read: Custom Exhibition Stand Design for Wine & Spirits Brands at ProWein 2027
Design for a 2.5-day B2B show
A short B2B show rewards a stand that is ready at the opening bell. That changes a few decisions.
Meeting capacity comes first. Business aviation deals start as conversations that run twenty minutes or an hour. One enclosed meeting room is the minimum for a mid-size stand. A second, smaller discussion area keeps the first from being booked solid by Wednesday afternoon.
Book appointments in advance. Book the install team and transport against the organizer’s published setup window, April 7 to 13. Vehicles must be out of the halls by 8:00 p.m. on April 13, and the stand has to be ready when the show opens on April 14.
Plan for the Friday close. The hub closes earlier on Friday, April 16, so check the exact time on the organizer’s opening hours page. Staff the stand for the morning, and decide in advance who will pack and who will stay on for the rest of the show on April 17, if you are present then.
Put the aircraft or product where people can see it. If you show a model, a cabin mock-up or a screen, give it a clear sight line from the aisle. A visitor decides in a few seconds whether to turn in. What happens after that matters more.
Keep storage and hospitality out of sight. Coffee equipment, brochures and spare materials belong in a closed back-of-house area. Visible clutter tells visitors the stand is busy or untidy.
Hall A1, the Dome or the static display
The organizer's registration page lists Hall A1, Hall A2, Hall A3, the static display and the Business Aviation Dome as exhibit areas. The right choice depends on what you are showing.
Check with the organizer how each area is priced and where each sits relative to the entrance. The registration page notes that a change of exhibition area is possible after registration is complete, which gives you room to adjust once the floor plan is published.
Also Read: How to Choose the Best Exhibition Stand Builder for ITB Berlin 2027
Build a timeline around what is still unknown
Returning AERO exhibitors had until the end of June 2026 to reserve their regular stand location for 2027. I found no published deadline for new exhibitors, so ask directly.
Work backward from April 14, 2027:
- Now: confirm your registration status and ask for the Hall A1 plan and technical guidelines.
- Once the plan is out: fix the stand size, the open sides and the number of meeting rooms.
- After the guidelines are published: lock height, rigging, electrical and flooring details, and file any required drawings.
- Early 2027: finalize graphics, product or aircraft display, and the meeting schedule.
- Before arrival: confirm the 2027 setup and dismantling times, then book the install team and transport.
The organizer’s 2027 Special Conditions of Participation set the setup and dismantling windows. Dismantling runs from Saturday, April 17 to Tuesday, April 20 at 8:00 p.m. Early setup before April 7 needs approval from the organizer’s project team.
Frequently Asked Questions
When is the business aviation part of AERO 2027?
April 14–16, 2027, in Hall A1 and the Business Aviation Dome. The show as a whole runs through April 17.
Does Hall A1 have its own entrance?
The organizer says yes, along with the Business Aviation Stage.
Can new exhibitors still book?
Yes. The organizer's registration page invites new exhibitors, though I found no published cutoff date. Contact the organizer to confirm availability.
Are the 2027 setup times published?
Yes. The organizer’s 2027 Special Conditions of Participation give setup from April 7 to 13, with vehicles out of the halls by 8:00 p.m. on April 13, and dismantling from Saturday, April 17 to Tuesday, April 20 at 8:00 p.m. Early setup before April 7 needs approval from the organizer’s project team.
Next step
If you have a Hall A1 position or are about to request one, send us the stand size, the number of people you'll staff it with and the meetings you want to run. We'll tell you what layout fits and what questions to put to the organizer first.
Related Reading: Seven Best Exhibition Stand Builders for ICE Europe 2027 in Munich

Ready to Build an Exhibition That Performs?
Whether it's a fully custom build, or a multi show programme, we're here to help you plan it. Let's start the conversation.
Whether it's a fully custom build, a pop-up system, or a multi-show programme, we're here to help you plan it. Let's start the conversation.